SAMPLE KNOWLEDGE OBJECT · 6.1.2.1–6.1.2.2
Hazard Identification & Risk Assessment
ISO 45001 Implementation System / Planning
How to use this Knowledge Object
Start with the implementation steps. Use the auditor questions and evidence checks to challenge your own system. Choose a Quick Win when you need a focused practical improvement, and finish with the self-check.
Executive Summary
A risk assessment is useful only when it changes how work is planned, controlled and improved. An impressive risk register is not evidence of effective risk management if the risks it describes are absent from management decisions—or the controls it assumes do not work on the shop floor.
This Knowledge Object provides a practical route from hazard identification → evaluation of existing controls → assessment of risk → additional controls → verification → review. It also addresses a frequently missed distinction: ISO 45001 expects organisations to assess not only OH&S risks arising from hazards, but also other risks to establishing, implementing, operating and maintaining the OH&S management system.
A strong system can demonstrate that:
- Hazards are identified proactively, including before changes and during non-routine work.
- Workers and relevant contractors contribute knowledge about work as actually performed.
- Assessment criteria are defined, applied consistently and documented.
- Existing controls are assessed for effectiveness, not simply copied into a register.
- Risk reduction follows the hierarchy of controls.
- Actions have owners, deadlines and effectiveness checks.
- Leaders understand the highest risks, and the organisation responds when conditions change.
Start with one critical activity. Go to where the work is performed. Ask the people doing it what could cause injury or ill health, and compare their answers with the risk assessment. This is often more informative than reviewing an entire register from a desk.
ISO Requirement — What It Means in Practice
Clause 6.1.2.1 — Hazard identification
The organisation needs an ongoing, proactive hazard-identification process. It should consider more than routine operational tasks and more than obvious physical hazards.
Relevant considerations include:
- How work is organised: workload, working time, social factors, bullying, harassment, leadership and culture.
- Routine and non-routine activities, maintenance, breakdowns, cleaning, changeovers, start-ups and abnormal conditions.
- Infrastructure, equipment, materials, substances, workplace conditions and the design of work.
- Human factors and the way work is actually performed, including the suitability of tasks and equipment for workers.
- Previous relevant incidents and emergencies, including their causes, and potential emergencies.
- Workers, contractors, visitors and people in the vicinity; people working at locations outside the organisation's direct control.
- Hazards created by activities near the workplace, as well as nearby situations beyond the organisation's control.
- Existing, proposed and temporary changes; new information and knowledge about hazards.
Hazard identification should be part of normal work planning and decision-making, not merely an annual paperwork exercise.
Clause 6.1.2.2 — Two risk assessments, not one
A. OH&S risks arising from identified hazards. Assess credible risks of work-related injury or ill health, considering how effective the existing controls are.
B. Other risks to the OH&S management system. Assess risks that could prevent the management system from being established, implemented, operated or maintained effectively. Examples include insufficient competence, unreliable contractor arrangements, inadequate resources, weak worker participation, ineffective change management or poor assurance of critical controls.
These two categories can interact, but they are not identical. A forklift–pedestrian collision scenario is an OH&S risk; lack of competent assessors across several sites may be a management-system risk. Use methods suited to each rather than forcing them into one numerical matrix.
The organisation must define its OH&S risk assessment methodology and criteria with an appropriate scope, nature and timing so assessments are proactive and systematic. The methodology and criteria are to be maintained and retained as documented information. A simple 5×5 matrix is an optional organisation-designed tool, not a scoring method mandated by ISO 45001.
Related boundaries: Assessment of OH&S opportunities and other opportunities is addressed in 6.1.2.3. Planning actions in response to risks and opportunities is addressed in 6.1.4; eliminating hazards and reducing risks through operational controls is covered further in 8.1.2. Applicable legal requirements must also be considered under 6.1.3.
Business Objective
The aim is to prevent work-related injury and ill health and enable informed operational decisions.
A functioning process helps the organisation:
- Decide which activities, exposures and failure modes require immediate attention.
- Direct investment to effective engineering and other higher-order controls.
- Identify where the work system, supervision or resources undermine safety.
- Test the assumptions behind existing assessments against actual practice.
- Involve workers in decisions that affect their health and safety.
- Anticipate hazards during procurement, new installations, expansion and other changes.
- Track whether risk reductions were actually achieved.
- Connect risk findings to competence, maintenance, contractor control, emergency preparedness, objectives and management review.
Business test: Can the organisation name three important OH&S risks, explain why they matter, identify the controls that prevent harm, show evidence those controls function, and describe the next improvement? If not, the register alone is not delivering enough value.
Implementation Guide
Step 1 — Define the assessment scope and ownership
Map processes, locations and work activities rather than beginning with the risk-register spreadsheet. Include production, warehousing, maintenance, laboratories, utilities, administration where relevant, transport interfaces, off-site work, contractors and temporary activities.
Identify who owns each assessment, who has technical competence, who must be consulted, who can approve acceptance of residual risk, and who can stop unsafe work.
Define whether a task-based assessment, exposure assessment, job safety analysis, permit-to-work review, specialist study or management-system risk review is appropriate. One format will not fit every hazard.
Example — warehouse: The scope includes routine picking, forklift travel, battery charging, trailer docking, maintenance, cleaning, peak-season temporary workers and third-party delivery drivers—not just ordinary forklift operation.
Output: Assessment scope, named process owners, competence requirements and worker-participation arrangements.
Step 2 — Identify hazards proactively
Walk the task from preparation through completion, including start-up, abnormal operation, cleaning, maintenance and recovery from failure. Interview people who do the work on different shifts and contractors where relevant.
Ask:
- What energy, substances, movements or exposures could cause harm?
- What happens if a barrier, guard, procedure or supervision fails?
- What changes when workload, time pressure or staffing varies?
- Who could be affected, including visitors and nearby workers?
- Which risks appear only during breakdowns, maintenance or emergency response?
- What do near misses, sickness trends, exposure measurements and worker reports tell us?
- Does the task design fit the abilities and needs of the people performing it?
Consider physical, mechanical, electrical, chemical, biological, ergonomic and psychosocial hazards. Do not allow a broad category such as “moving machinery” to replace a specific, assessable scenario.
Better description: “Forklift reverses from the dispatch staging area across an unsegregated pedestrian route during afternoon peak loading.”
Weak description: “Forklift hazard.”
Output: A set of clearly stated, credible exposure or harm scenarios linked to the real activities and people affected.
Step 3 — Define and apply risk assessment criteria
Establish a documented methodology before scoring risks. Describe the scope, nature and timing of the assessment; the criteria; any risk thresholds; responsibilities; use of specialist assessment; and review triggers.
For each hazard:
- Define the credible consequence and the conditions in which exposure could occur.
- Identify current controls and verify their presence and effectiveness in practice.
- Evaluate risk using the organisation's defined criteria. A severity × likelihood score may be suitable for some scenarios, but is not universally suitable or sufficient.
- Consider exposure frequency, duration, numbers exposed, uncertainty and potentially catastrophic outcomes as relevant to the chosen method.
- Determine whether further risk reduction is necessary and which findings require escalation or immediate safeguards.
- Record the rationale, the people consulted and any limits of available information.
Critical distinction: An assessment of risk with current controls is not the same as a forecast of risk after planned improvements. If projected residual risk is shown, label it as projected. Do not treat proposed controls as effective until implemented and verified.
For issues such as occupational chemical exposure, noise, vibration, psychosocial risks or complex machinery, use competent specialist methods and applicable exposure limits rather than relying only on a generic 5×5 matrix.
Output: Defined risk criteria, assessments linked to control effectiveness, and documented decisions.
Step 4 — Assess other risks to the OH&S management system
Create a focused review of issues that could prevent the system from delivering its intended outcomes. Use organisational context, interested-party needs, audits, incidents, leadership discussions and performance data as inputs.
Examples:
- High turnover means supervisors cannot consistently verify safe working practices.
- Critical contractor controls vary across sites and contracts.
- Risk assessments are authored centrally but do not reflect local operations.
- Production changes bypass the management-of-change process.
- Workers cannot easily report hazards or believe concerns will not be acted upon.
- A single specialist holds all the knowledge required for a critical statutory process.
For each system-level issue, document the potential consequence, affected system processes, existing safeguards, owner, required actions and how the organisation will know that the safeguard works.
Output: A management-system risk review with assigned mitigation actions. It may be integrated into an existing business-risk process if OH&S implications remain visible and managed.
Step 5 — Select additional controls using the hierarchy
Prefer eliminating the hazard when feasible; then consider substitution, engineering controls, administrative controls and personal protective equipment.
Do not treat training or PPE as the default answer to every significant risk. Select controls based on the specific failure mechanisms and the circumstances of the work.
Forklift example:
- Elimination: Remove pedestrian access from the dispatch movement zone by redesigning the material flow.
- Substitution: Consider a safer handling method where feasible.
- Engineering: Install fixed segregation barriers and protected crossings.
- Administrative: Establish traffic rules, authorisation, inspections and clear instructions for visiting drivers.
- PPE: High-visibility clothing as supplementary protection, not a replacement for physical separation.
Assign an action owner, due date, interim controls, required resources and criteria for verifying implementation. Escalate risks that cannot be adequately controlled; do not automatically accept them because a matrix labels them “medium.”
Output: Prioritised control improvement actions connected to hazard assessments.
Step 6 — Implement, verify and reassess
After installing or changing controls, verify they function under normal and reasonably foreseeable abnormal conditions.
Test performance through workplace observations, inspections, maintenance records, exposure monitoring, worker interviews, drills or other evidence relevant to the control. Reassess the risk using the established method, including remaining exposure and potential failure modes.
An installed barrier is evidence of an action completed. Evidence that workers and vehicles remain segregated during peak shifts is stronger evidence of effectiveness.
Do not mark an action effective simply because a revised procedure has been distributed or workers attended training.
Output: Implementation and effectiveness evidence, reassessed risk, and a recorded closure decision.
Step 7 — Establish ongoing reviews and change triggers
Review promptly when relevant conditions change—for example new equipment, new substances, changed layout, work organisation, contractor interface, relevant incident or near miss, new hazard information, evidence of control failure or new legal requirements.
Use proactive change assessment before implementation where possible. Periodic review can help catch drift, but a calendar-only review process is insufficient.
Track versions of assessment criteria and keep the assessments and other required records according to the organisation's documented-information rules and applicable law.
Output: Evidence that assessments are current and that significant changes generate timely risk review.
Step 8 — Connect risk decisions to the wider OH&S management system
Trace significant issues into:
- Leadership decisions and resource allocation (5.1, 7.1).
- Worker consultation and participation (5.4).
- Planning actions and objectives (6.1.4, 6.2).
- Competence and awareness (7.2, 7.3).
- Operational planning and control (8.1).
- Management of change and contractor arrangements (8.1.3, 8.1.4).
- Emergency preparedness and response (8.2).
- Monitoring, internal audit and management review (9.1, 9.2, 9.3).
- Incident investigation and corrective action (10.2).
Practical trace: Significant hazard → risk decision → chosen control → accountable manager → evidence of implementation → evidence of effectiveness → follow-up and management review.
Auditor Perspective
An experienced auditor may start by asking leadership, “What are your biggest OH&S risks?” This reveals risk awareness and ownership. It is an effective opening, not a prescribed sequence that every auditor must follow.
A useful audit then tests the full chain:
- Interview leadership about significant risks and improvements.
- Select a critical activity or exposure scenario.
- Observe the workplace and speak with workers and supervisors.
- Review the associated hazard identification and risk assessment.
- Confirm how existing controls were evaluated and how additional controls were selected.
- Test records, observations and performance data for evidence that controls work.
- Check how changes and incident learning feed back into the assessment.
Audit trail — forklift/pedestrian interface: Leadership reports vehicle–pedestrian collision as a top risk. The risk assessment identifies the relevant loading routes and conditions. Physical barriers and protected crossings are specified. A site walk shows their real condition and use. Workers describe how visitor deliveries and peak loading are handled. Maintenance and inspection records show that critical protections are checked. Near misses and changes to layout have been reviewed. This is stronger than a risk register with a low residual score and no evidence.
Another audit trail — management-system risk: High temporary-worker turnover is identified as a competence risk. The organisation introduces task-specific verification before independent work, supervisor observation and translated induction where appropriate. Sampling across shifts shows how the process works, not just that a training list exists.
Warning: A numerical reduction from 15 to 5 is not proof of safer operations unless the criteria and underlying control changes are justified and verified.
Auditor Questions — A Focused Question Bank
Leadership and priorities
- What are the three most significant OH&S risks to this operation and why?
- Which risk-reduction investments have you approved in the last 12 months?
- Which high risks remain, and who owns the decisions about them?
- How do leaders know that critical controls are effective?
Hazard identification and participation
- How are non-routine, maintenance and contractor activities assessed?
- How do workers contribute to identifying hazards and improving controls?
- How are psychosocial hazards and work organisation considered?
- How are hazards affecting people outside the immediate work area identified?
- Show an example of a hazard identified before an incident or change.
Methodology and assessment
- What documented criteria are used, and why are they suited to these activities?
- How are the scope, timing and competence of assessments determined?
- How is the effectiveness of existing controls taken into account?
- What happens when evidence is incomplete or a specialist evaluation is needed?
- How does the organisation manage risk that cannot yet be adequately controlled?
Implementation and review
- Show a case in which a higher-level control replaced a weaker one.
- What evidence confirms that a new control works under operational conditions?
- How did the last incident or near miss change an assessment?
- How are risks assessed before planned changes?
- How do you decide when a risk assessment must be reviewed?
Other risks to the management system
- What could prevent the OH&S management system from working as intended?
- How are competence gaps, contractor arrangements and resource constraints evaluated?
- Where are these system-level risks recorded and reviewed?
- What has changed because of the review?
Auditor's Thinking — What the Answers Reveal
| Area | What the auditor is testing | Strong evidence | Warning signs |
|---|---|---|---|
| Leadership | Risk ownership and decision-making | Leaders explain specific hazards, investments and open issues | Leaders cannot explain priority risks without calling HSE |
| Hazard identification | Coverage of work as performed | Non-routine work, shifts, contractors and worker input are visible | Generic lists copied from another location |
| Methodology | Consistency, appropriateness and documented criteria | Defined method, clear rationale, competent application | Scores entered without evidence or criteria |
| Control effectiveness | Whether assumptions match reality | Field checks, maintenance, worker observations, trend evidence | “Control in place” is accepted without verification |
| Hierarchy of controls | Whether prevention is prioritised | Elimination/engineering options evaluated and implemented | Training/PPE offered as the universal solution |
| Change management | Proactive rather than reactive approach | Assessment before equipment/layout/process changes | Risk register updated only after an event |
| System-level risks | Ability of the management system to function | Competence, resources, contractor governance and participation reviewed | Only injury scenarios assessed; systemic weaknesses ignored |
| Improvement | Evidence that risk reduction is real | Before/after verification, action follow-through | Lower numeric scores with no changed conditions |
Interpretation caution: The absence of any single example above does not automatically establish an ISO nonconformity. The auditor must relate facts and evidence to applicable requirements and the organisation's context.
Objective Evidence — What to Look For
A proportionate evidence package can include:
- Documented hazard-identification and risk-assessment methodology and criteria, including scope, nature, timing, responsibilities and review triggers.
- A representative sample of assessments covering routine and non-routine activities, relevant groups of people, abnormal conditions and significant hazards.
- Evidence of worker consultation and participation: interviews, workshop outputs, safety observations, reporting records and response to suggestions.
- Evaluation of existing controls: inspections, engineering verification, guarding checks, exposure measurements and relevant maintenance records.
- Relevant action plans showing control options considered, decisions made, ownership, resources and completion criteria.
- Records demonstrating that implemented controls were verified for effectiveness and risk reassessed when needed.
- Change-management records, incident learning, procurement and contractor-control links.
- Evidence of assessment and treatment of other risks to the OH&S management system.
- Management review, objectives and investment decisions traceable to important risks.
What does not prove effectiveness by itself: A signed matrix, a recently revised procedure, an attendance list, or an action marked “closed.” These may be useful components of evidence; they need corroboration.
Common Nonconformities and Weaknesses
Potential findings must be substantiated against actual requirements and evidence. Common weaknesses include:
- Incomplete hazard coverage: Maintenance, contractor work, abnormal operations or psychosocial factors are missing without justification.
- Generic assessments: A standard list does not describe the actual task, affected people or exposure scenario.
- Unverified assumptions: Controls are named but are absent, bypassed or unreliable in the workplace.
- Undefined or undocumented criteria: Risk scores cannot be explained or reproduced consistently.
- Scoring hides serious hazards: A low overall score substitutes for consideration of severity, credible failure and legal controls.
- No management-system risk assessment: Weaknesses in resources, competence, consultation or governance are not considered.
- Weak worker participation: Assessments are produced without the knowledge of people performing the activity.
- Hierarchy not applied: Administrative rules or PPE are selected without reasonable consideration of more effective risk reduction.
- Change not reflected: New equipment, substances, layouts or work organisation are implemented without timely review.
- Action closure without evidence: The improvement is marked complete before effectiveness is established.
- No learning loop: Near misses and investigations do not inform hazard identification or controls.
- No link to decisions: Significant risks do not influence objectives, resources or operational planning.
Audit judgement: A finding requires a clear requirement, objective evidence and a defensible explanation of the gap. These examples are audit indicators, not automatic certification verdicts.
Best Practices — What Good Looks Like
- Use short, task-based hazard reviews where the work happens, supported by deeper specialist studies where needed.
- Ask affected workers about workarounds, shortcuts and conditions during busy or unusual periods.
- Record the credible failure scenario—not only the hazard category.
- Identify critical controls and set clear verification arrangements.
- Keep current risk and projected post-action risk distinct.
- Use different assessment methods where hazard types or system-level issues require them.
- Review risks before changes; use incident learning to test and revise controls.
- Connect significant risk-reduction projects to business investment and performance review.
- Focus on quality of risk decisions and effectiveness, not the number of rows in the register.
AI Prompts — Guided Workflows
AI-generated content is a starting hypothesis, not a competent workplace risk assessment. Do not provide confidential personal or commercially sensitive information to unapproved AI services. Verify legal requirements, specialist exposure methods and proposed controls using competent personnel and workplace evidence.
Prompt 1 — Challenge hazard-identification coverage
Act as an ISO 45001 OH&S auditor and help identify potentially overlooked hazards.
Context: [industry, activity, location, equipment, workers/contractors/visitors, working hours, non-routine operations, known incidents].
Existing hazard list: [paste an anonymised list].
Return a table with: activity; credible exposure/harm scenario; people affected; overlooked condition; questions to verify on site; suggested evidence source.
Include work organisation and psychosocial factors, emergencies, abnormal work and planned changes.
Do not assert that an unverified hazard exists. Mark assumptions and information gaps clearly. Do not assign final risk scores.Prompt 2 — Review assessment methodology
Review the following OH&S risk assessment methodology for consistency and practical use: [insert methodology and criteria].
Check whether scope, nature, timing, competent assessors, worker participation, existing-control effectiveness, scoring rules, uncertainty, escalation and review triggers are clearly defined.
Separate likely ISO 45001 clause 6.1.2.2 issues from optional enhancements.
Produce: strengths; ambiguous rules; potential gaps; five questions for the process owner; suggested revisions.
Do not invent a scoring method or claim certification compliance.Prompt 3 — Compare controls with actual work
Using this anonymised task description [task] and risk assessment [assessment], build a workplace verification plan.
For each claimed control, list what to observe, whom to interview, which records to sample, what failure modes to check and how to document the result.
Prioritise critical controls. Flag unknowns; do not assume controls are effective because they are documented.Prompt 4 — Analyse other risks to the OH&S management system
Help identify other risks to an ISO 45001 OH&S management system (clause 6.1.2.2), distinct from direct injury/ill-health scenarios.
Context: [organisational context, resources, turnover, contractor model, leadership, worker participation, audits and current changes].
Return a table: management-system risk; affected system process; plausible effect; existing safeguard; evidence needed; proposed action; accountable role.
Do not invent facts about this organisation. Link each hypothesis to a verification question.Prompt 5 — Prepare a risk-based audit trail
Create an ISO 45001 audit trail for [high-risk activity] using [anonymised risk assessment and control information].
Use sequence: leadership awareness → work observation → worker interview → risk assessment → existing controls → improvements → effectiveness verification → management review.
Provide 10 focused interview questions and the evidence expected at each stage.
Distinguish evidence gaps from confirmed nonconformities; do not assert a finding without objective evidence.Related Knowledge Objects
Risk identification and control are connected to the wider OH&S management system. Explore these topics through the Implementation System Knowledge Objects index:
- Context of the Organization — factors affecting OH&S priorities
- Leadership & Commitment — ownership, decisions and resources
- Consultation & Participation of Workers — worker knowledge and involvement
- Actions to Address Risks & Opportunities — action planning and follow-through
- Legal & Other Requirements — obligations shaping controls
- Operational Planning & Control — implementation in daily operations
- Management of Change — risks before planned changes
- Contractors — third-party interfaces
- Emergency Preparedness & Response — foreseeable emergencies
- Internal Audit — independent challenge
- Management Review — performance, escalation and decisions
- Incident, Nonconformity & Corrective Action — learning and improvement
Quick Wins — Practical Improvements You Can Make Now
These short actions help you strengthen the hazard identification and risk assessment process as part of everyday OH&S management. Use them to identify a meaningful improvement, test an important assumption or close a practical gap. They are not a substitute for the full implementation steps above, and they are not a stand-alone audit-preparation programme.
- Ask three leaders to name the top OH&S risks. Compare the answers, then verify what the organisation is doing about them.
- Walk one critical task. Confirm that the written hazard scenarios and controls match how work happens on an ordinary busy shift.
- Check the method, not just the scores. Confirm the organisation can explain its criteria and why current controls are considered effective.
- Take one recently completed action. Check whether effectiveness was verified before the risk assessment was updated.
- Review one change or near miss. Trace how it influenced hazards, controls and worker communication.
- Identify one system-level vulnerability. For example, a contractor governance gap or competence bottleneck, and verify who owns it.
Each quick action should produce a useful outcome: a verified strength, a clearly identified gap, or an improvement action with an owner. Choose the actions that matter most to your operation rather than treating this as a mandatory checklist.
Practical Example — From Register to Reality
Scenario: A distribution warehouse has repeated near misses between pedestrian pickers and forklifts near dispatch. The risk register labels “vehicle movement” as medium risk because drivers have been trained and everyone wears high-visibility clothing.
Reality check: During peak hours, pedestrians cut across a temporary staging area. The marked route is blocked by pallet overflow. Visitors do not always receive the same briefing. The assessment assumes the route remains clear.
Better hazard statement: “Pedestrians enter an active forklift crossing during peak loading when the marked walkway is obstructed; credible outcome is serious crush injury or fatality.”
Existing controls to verify: Route markings, speed restrictions, driver competence, supervision, visitor access arrangements, inspection of routes. Record whether they actually function during peak loading—not just whether procedures mention them.
Improvement: Eliminate unnecessary crossing where possible, physically separate pedestrians and forklifts, redesign the staging area and add controlled visitor access. Administrative checks remain supportive controls.
Effectiveness test: Observe multiple peak periods and shifts after the change; examine route-obstruction reports and near misses; speak with pedestrians, operators and visiting drivers. If barriers or routes fail under operating pressure, the issue remains open.
System-level insight: The same problem may reveal weak temporary-layout change management or poor contractor communication. Assess and address those system-level risks in addition to the specific collision scenario.
What an auditor can follow: Hazard identified → risk assessed → controls selected → management approved resources → physical change completed → evidence of improved separation → risk reviewed → lessons fed into change control.
Final Self-Check — Does Your System Work?
Use these questions with a process owner or during an internal audit.
Decision rule: If any answer is uncertain, select one representative process and verify it with workers and objective evidence before declaring the system effective.
Your checkmarks stay in this browser.
